Tel: 64-9-478 7378  /  Fax 64-9-478 7328     Email : highperformancemodels@xtra.co.nz

SPECIALISTS IN R/C PERFORMANCE MODEL BOATS FOR MEN .................................NO TOYS FOR BOYS

 

  

#GRP2347 JET PROPULSION UNIT 5 

The new JET propulsion unit is ideal for internal combustion engines, as thrust reversal is obtained by operating the reversing flap rather than by reversing the direction of rotation of the engine. Suitable power plants are internal combustion engines of 15 to 30 cc capacity, recommended Zenoah 26cc Petrol Engine and electric motors rated at a minimum of 700 Watts output power.

  • US$262.00

  • NZ$ 399.00

#GRP2221.3 PIN COUPLING

   

This Flexible 3 Pin Coupling is used to connect the Jet Propulsion Unit to the Zenoah Petrol Engine
  • LENGTH 150mm x 30mm diameter
  • SHAFT 7mm diameter x ENGINE M6
  • US$ 147.00

  • NZ$ 225.00

       

#GRP2340 JET PROPULSION UNIT

   
  • Length approx. 250 mm
  • Length incl. reversing
  • Mechanism approx. 290 mm
  • Width approx. 58 mm
  • Height approx. 70 mm
  • NZ PRICE  NZ$ 175.00

 

 
The Jet unit No. 2340 used with 2340.1 reversing mechanism and toothed belt reducer No. 2341 are designed for the SPEED 700 BB TURBO MOTOR. Hull length can be approximately 1200mm long.  For higher speeds ULTRA motors or an internal combustion motor can be used if preferred; this is left up to the modeler's discretion and experience.
The set contains: inlet duct (2-part, vacuum-molded in ABS plastic), impeller pipe, 40 mm Ø impeller, outlet jet, guide vanes, steering jet (all parts injection-molded plastic), 5 mm Ø shaft with one ball race, 8 mm Ø stern tube.

#GRP2340.1 Water Jet reversing Mechanism $50.00

  • NZ PRICE  NZ$ 50.00

 

The set contains: flap, control yoke and mounting lugs

All parts injection-molded plastic.

#GRP2341 JET PROPULSION UNIT GEAR BOX

   

The set contains: gearbox flange, two toothed belt pulleys, toothed belt. Required for high-revving electric motors, as it reduces current drain by about half.
  • NZ PRICE  NZ$ 59.00

 
       

#GRP2345 JET PROPULSION UNIT 2

Kit includes :

  • Suction Pipe (2-part, vacuum-molded in ABS plastic, XCNC machined )
  • Impeller Tube
  • 29 Diameter Impeller
  • Outlet Jet
  • Guide Vanes
  • Stern Tube
  • NZ PRICE  NZ$91.00

 
This Propulsion unit fitted with control jet & reversing mechanisms 2345-1 can be used with SPEED 700 BB Turbo motor, the units can be installed with other similar motors.
The kit contains: suction pipe (2-part, vacuum-molded in ABS plastic, CNC-machined), impeller tube, 29 mm Ø impeller, outlet jet, guide vanes (all parts injection-molded plastic), stern tube 1
   
     

#GRP2345-1 CONTROL JET

Kit includes :

  • Control Jet
  • Tiller
  • Reversing Flap
  • 2 Lugs
  • All parts are injection-moulded Plastic
  • NZ PRICE  NZ$50.00

 

 
       

#GRP2349 MINI JET

   

  • Length approx. 110 mm
  • Length incl. reversing flap approx. 130 mm
  • Width max. approx. 58 mm
  • Height approx. 50 mm
  • Impeller Ø 19 mm
  • Weight approx. 35 g (excl. coupling)
  • NZ PRICE  NZ$75.50

The Mini-JET is Suitable for SPEED 500 and 600 electric motors. and can be used for small and medium-sized boats. It provides very accurate control in forwards and reverse mode alike. All parts are injection-moulded in plastic except the shaft, which is of 3 mm Ø stainless steel. It is sealed at one end and runs in twin sintered bushes. The set includes the reversing flap and the motor coupling.    
       
       

 

 

 Tel: 64-9-478 7378  / Fax 64-9-478 7328 Email : highperformancemodels@xtra.co.nz

THIS WEBSITE IS DESIGNED & MAINTAINED BY KIM KOCKOTT